Click on this link if you need more information about a Flow meter.
The mass and volumetric
flowmeters of FMA-1600A
Series use the principle of
differential pressure within a
laminar flow field to deterime the
mass flow rate. A laminar flow
element (LFE) inside the
meter forces the gas into laminar
(streamlined) flow. Inside this
region, the Poiseuille equation
dictates that the volumetric flow
rate be linearly related to the
pressure drop along a fixed
distance of the LFE. This, along
with the viscosity of the gas, is
used to accurately determine the
volumetric flow rate. Separate
absolute temperature and
pressure sensors are incorporated
and correct the volumetric flow rate
to a set of standard conditions. This
standardised flow rate is commonly
called the mass flow rate and is
reported in units such as standard
cubic feet per minute (SCFM) or
standard litres per minute (SLM).
Standard units include a 0 to 5 V
output (4 to 20 mA optional) and
RS232 communications. The gas
select feature can be adjusted from
the front of the keypad or via RS232
communications. Volumetric flow,
mass flow, or absolute pressure, and
temperature can be viewed or recorded
through the RS232 connection. It is also
possible to multi-drop up to 26 units
on the same serial connection to a
distance of 38 metres. These flowmeters
can be powered by the optional battery
pack FMA1600-BP for use in the field.
SPECIFICATIONS Accuracy: ±(0.8% of rdg + 0.2% FS) Repeatability: ±0.2% Turndown Ratio: 200:1 Response Time: 10 ms typical default response time for 63.2% of a step change. A variable register allows response time to be field adjustable to a certain extent via RS232 communications. The primary trade-off for response time is signal noise Output: 0 to 5 Vdc standard Operating Temperature: -10 to 50°C (14 to 122°F) Zero Shift: 0.02% FS/°C/atm Span Shift: 0.02% FS/°C/atm Humidity Range: 0 to 100% non-condensing Pressure (Max): FMA-1600A Series: 145 psig FMA-1600A Series: 50 psi differential FVL-1600A Series: 10 psig FVL-1600A Series: 10 psi differential Measurable Flow Rate: 125% FS Supply Voltage: 7 to 30 Vdc (15 to 30 Vdc for 4 to 20 mA output) Supply Current: 35 mA typical current draw; 100 mA available supply recommended Cable Connection: 8-pin mini DIN Wetted Parts: 303 & 302 Stainless Steel, FKM Heat Cured Silicone Rubber, Glass Reinforced
Polyphenylene Sulfide, Heat Cured Epoxy, Aluminum, Gold, Silicon, Glass. Contact Omega engineering for details.
Standard Pressure Drops (venting to atmosphere):
Max Flow Rate
0.5 to 50 SCCM
0.1 to 10 SLM
† All amounts shown in EUR Note: Comes complete with 24 Vdc power supply with 1.8 m of cable, 8 pin male mini DIN connector, operator’s manual and NIST certificate.
††Portable versions "-B" have an integral battery compartment and come complete with 24 Vdc power supply, 8 pin male mini DIN connector, operator's manual, NIST certificate, and 9V battery installed. Portable version is not available on models with 4 to 20 mA output.
Units are calibrated to air @ 5 psig for 0 to 1 LPM, 15 psig for 2 to 10 LPM, 30 psig for 20 to 100 LPM, and 50 psig for 200 LPM and greater.
Calibrations done at ambient (21°C/70°F) temperature only.
To replace the standard RS232 communications with RS485, add suffix "-RS485" to the model number, contact sales for additional price.
Standard output is scaled to the mass flow rate. For volumetric flow rate as standard output add "-VOL" to the model number.
Optional secondary output are scaled the same as the primary output. For a different secondary output scale add suffix "-T" for temperature or suffix "-P" for pressure, no additional cost.
Add "-SCFH" to model number for units scaled in SCFH, no additional charge. Specify required range in SCFH.
For totalizer option, add suffix "-TOT" to the model number, contact sales for additional price. Please specify resolution. This is a 6-digit counter. Examples: For totalizing in litres with 1/100 litre resolution, the max count would be 9999.99. For totalizing in litres with 1 litre resolution, the max count would be 999999.
High accuracy calibrations to ±0.5% of full scale are available on models having a minimum full scale range of 10 SCCM or greater. For a high accuracy calibration add suffix "-HACAL" to the model number, contact sales for additional price.
For a Remote Display, add suffix "-RD-*FT" to the model number, contact sales for additional price. Replace the * in the suffix with the required length in whole feet, the maximum length is 12'. Please note the optimum distance in feet is between 9 to 10'.
Part Number Builder
Build Your Part Number Below
Max Flow select from: 01 for 0.5 SCCM 02 for 1 SCCM 14 for 2 SCCM 15 for 5 SCCM 03 for 10 SCCM 16 for 20 SCCM 04 for 50 SCCM 17 for 100 SCCM 18 for 200 SCCM 19 for 500 SCCM 20 for 1 SLM 05 for 2 SLM 06 for 5 SLM 07 for 10 SLM 08 for 20 SLM 09 for 50 SLM 10 for 100 SLM 11 for 250 SLM 12 for 500 SLM 13 for 1000 SLM 21 for 1500 SLM 22 for 2000 SLM 23 for 3000 SLM
Output select from: Nothing(leave field blank) for None -I for 4 to 20 mA output -I2 for Two 4 to 20 mA outputs -V2 for Two 0 to 5V Outputs -I2-T for Two 4 to 20 mA outputs second output for temperature -V2-T for Two 0 to 5V outputs second output for temperature -I2-P for Two 4 to 20 mA outputs second output for pressure -V2-P for Two 0 to 5V outputs second output for pressure -VOL for Volumetric flow rate as standard output
Portable Version select from: Nothing(leave field blank) for Standard -B for Portable version of the meter (not available on models with 4 to 20 mA output)
Input select from: Nothing(leave field blank) for 0 to 5V -IN for 4 to 20 mA input
RS485 select from: Nothing(leave field blank) for RS232 -RS485 for RS485
SCFH select from: Nothing(leave field blank) for Standard -SCFH for Units scaled in SCFH
Totalizer select from: Nothing(leave field blank) for Standard -TOT for Totalizer
Note: All combinations may not be valid, check spec sheet for valid part numbers.